Reinforcing mixture "THERMO-FASAD"

Is Negotiable

Contact information

Konichenko Aleksey Vladimirovich

Finansial manager
+380993769736, +380713216478
Email

Payment Types
Prepayment
Transportation Types
Automobile transport
Minimum Order Size
discussed

Adhesive mixture

APPLICATION: Adhesive mixture “Green Thermo “Termo-Fasad” is intended for the device of a protective layer and also for gluing facade polystyrene plates on the surface of brick, concrete, cement-sand, cement-lime, plaster and other mineral substrates. Glutinous mixture can be used inside and outside buildings in industrial and residential areas. This layer can be a basis for finishing decorative plasters and putties. It is also possible to glue and reinforce hard mineral wool boards.

COMPOSITION: Adhesive mixture "Green Thermo "Thermo-facade" is made of high-quality Portland cement, mineral aggregate as well as modifying additives that improve the physical and mechanical properties and adhesion.

PREPARATION OF THE FOUNDATION: The preparation of the substrate is carried out in accordance with SNiP 3.04.01-87 and DBN B.2.6-22-2001. The substrate must be sufficiently strong and even, free from dust, dirt, lime, grease or oil paints. Fragile areas of the base must be removed. Silicone absorbent substrates must be treated with one of the deep penetrating emulsions of Green Thermo and allowed to wait for 4 hours before performing the work. Before installing the protective reinforcing layer it is necessary to perform mechanical fastening of the insulation plates (dowels). Any irregularities in the surface of the glued foam polystyrene boards should be sanded with abrasive paper fixed to a rigid semifinished. This operation can be performed after curing the adhesive after 3 days. Mineral wool plates are not polished.

IMPLEMENTATION: The dry mixture must be filled in a container of clean water at the rate of 0.24-0.26 liters of water per 1 kg of the mixture while mixing manually or mechanically until a homogeneous and elastic mass is obtained. After 5 minutes the solution mixture must be re-mixed after which it can be used for 1.5 hours. The layer is applied to the entire surface of the plate and leveled with a notched trowel or a spatula with 10-12 mm teeth. Before applying the main layer of the mixture " Green Thermo “Thermo-Fasad" to the insulation it’s surface must be primed with the same mortar. When using a continuous method, the mixture should be removed from the edges of the insulation by 10-15 mm. In any case the amount of solution should be such that the plate is connected to the base by not less than 60% of their area. The solution should not fall on the ends of the plates and the excess solution must be removed.

CONSUMPTION: The average consumption of the mortar mixture for gluing the slabs is 6 kg / m2 while the reinforced layer device is 5 kg / m2.

APPLICATION: Work should be carried out at a substrate temperature of +5 to + 30 ° C. All the above recommendations are effective at a temperature of + 20 ° C and a relative humidity of 60%. In other conditions the time for trimming, setting and hardening of the mortar mixture can change. Mixture "Green Thermo “Thermo-Fasad" contains cement and when interacting with water it gives an alkaline reaction. So it is necessary to protect eyes and skin when working. In case of contact with the solution rinse immediately with water and seek medical advice.

STORAGE: In original sealed packaging in dry premises for 12 months from the date of manufacture indicated on the package.

DISPOSAL CONSIDERATIONS: Dispose of product residues as construction waste. Dispose of the packaging as household waste.

PACKAGING: Mixture "Green Thermo" Thermo-Fasad" is packed in bags of 25 kg.

TECHNICAL CHARACTERISTICS

- Proportion of the mixture: .................................... 0.24-0.26 liters of water/kg

- Working time: ..................... no less than 1.5 hours

- Open time: .............................. not less than 20 minutes

- Adhesion to concrete: .................................... no less than 0.7 MPa

- Adhesion to the material .................................... min 0.08 MPa

- (cohesive rupture on the heater): ... after 7 days of hardening

- Frost resistance: ....................................... min 50 cycles

- Substrate temperature: .............................. + 5 ° C to + 30 ° C

- Operating temperature: ........................ -30 ° C to + 70 ° C

 

MANUFACTURER'S GUARANTEES: DSTU П B В.2.7-126: 2006, group Ц.1.Г13-3К5.

The manufacturer guarantees the compliance of the “Green Thermo “Thermo-Fasad” mixture with the specified technical characteristics when the implementing of rules of transportation, storage, preparation and application which are listed above. The manufacturer is not responsible for the incorrect using of the mixture.