Showing 1-5 of 5 items.

Is Negotiable

The epoxy single-pack glue УП 5-207М

Scientific-Production Enterprise “Synthes”, PE

Glue of increased heat resistance and adhesion to a variety of substrates.

Resistant to short-term exposure to temperatures of 250 ° C, combines stiffness, heat resistance with the ability to form vacuum-tight (under special conditions - vacuum-cleaned) adhesive joints in conditions of repeated thermal cycling from minus 60 ° C to 150 - 200 ° C. Excellent adhesion to gold (up to 30 MPa), beryl foil, polyamide, ceramics.

It is used mainly for mounting and sealing microcircuits incl. in multi-layer thin-film microassemblies.

More Email


Is Negotiable

The glue UVS 10 TC

Scientific-Production Enterprise “Synthes”, PE

It is a solution composition based on phenol-formaldehyde resins, hardeners, modifiers, adhesion additives, surfactants. They are used as adhesive compositions for various purposes, weather-corrosion-resistant coatings.

Supplied in ready to use form.

Store at room temperature for 6-8 months.

Operating temperature range up to 250 ° С, for short time 300-350 ° С.

 

Glues UVS-10TC developed and produced on the Ukrainian raw materials base as an analogue of the properties of adhesives ВС10Т, ВС-350, produced earlier in the USSR. The need for the development of adhesives was caused by the cessation of the production of one of the components of the adhesives - vinylflex.

 

Various modifications are available providing a specific set of properties. The experience of their use during the last 15 years has shown the complete identity and interchangeability of the previously produced glues VS-, BF-, BFR-, including confirmed by testing at OJSC  AVTOVAZ instead of BFT-52, VS10T.

More Email


Is Negotiable

The epoxy single-pack glue brand UP 16-06

Scientific-Production Enterprise “Synthes”, PE

One-pack (ready-to-use) structural adhesive sealant with increased heat resistance. The adhesive combines thixotropic properties and the ability to adjust the viscosity at the customer's request (depending on the application method). The use of this material allows to combine both homogeneous (metal-metal) and heterogeneous materials (ferrous and non-ferrous metals, stone, wood, ceramics, porcelain, plastic, fiberglass.) Special additives allow to exclude operations for cleaning, degreasing and surface preparation from the technological cycle.

It has a complex of properties and can be modified for the specific application of the Customer.

Product Feature:

- stored at room temperature for 4-8 months, in the refrigerator for 1-2 years.

- cures when heated to 120-150 C in 15-20 minutes.

- operating temperature range from -100 С to 200 С, for short time 250 С.

- does not contain solvents.

- the ability to glue oily metals.

- retains 90% of properties after aging in oils, lubricating and cooling liquids at 135 C during the year.

- possesses adhesion to a wide range of substrates and provides high adhesion strength: alloyed steel type 30ХГСА (up to 40 MPa), steel 35 (up to 34 MPa), titanium (up to 35 MPa), brass (up to 22 MPa), glass, coal, organic, hybrid plastics (destruction by plastic), ceramics (up to 25 MPa), gold (up to 30 MPa), kovara (up to 9 MPa), beryllium foil, sendasta, permalloy, alloy Neisilber (up to 6 MPa), ABS plastic, polyamide (plastic).

- provides tightness of adhesive joints at an excess pressure of up to 107 Pa or in a deep vacuum (helium leaks less than 3 • 10-7 l μm / s).

-stress to the effect of freon, oils, lubricating-cooling liquids, does not change the optical characteristics of instrument liquids, corrosion activity corresponds to a score of "0", mushroom resistance is 1-2 points.

Methods of application

The application of the material is carried out by Graco pistols, by screen printing.  It is allowed to apply with a spatula, brush.

Areas of use

It was developed according to the terms of reference and applied to JSC AVTO-VAZ before the introduction of robotics on the conveyor belt for anticorrosive protection and sealing of glued joints of perimeter flaps of doors, hoods, luggage carriers of VAZ, ZAZ, RAF, AZLK, GAZ.

Currently, the glue is used to paste carbide inserts in the manufacture of cutting tools (cutters, cutters, countersinks, hons, etc.).

Glue has found application for gluing magnets in stators and rotors of electric motors, gluing ceramic inserts in fuses, gluing of dissimilar substrates (fiberglass - copper or steel tip, etc.), bonding difficult-to-digest and hard-to-break metals and alloys (making plate and tubular heat exchangers, radiators from copper, brass, aluminum, duralumin, blocks of cylinders), restoration of bearing seats, manufacturing and installation of sensors, electric motors, etc.

It is also used for the manufacture of rotary racks of railway cars. There is an experience of pasting babbitt bearings in the compressor equipment.

It is developed and applied in technology of restoration of necks of shafts, landing places on shafts, shafts gear wheels.

More Email


Is Negotiable

The epoxy single-pack glue brand UP 16-07

Scientific-Production Enterprise “Synthes”, PE

One-packing glue-sealant UP 16-07 is specially developed and fully adapted to the technology of gluing and sealing of suction plastic silencers for compressors of refrigerators Minsk. Special additives allow you to glue polystyrene, ABS plastic, providing structural strength and tightness of the adhesive seam.

 

Adhesive has adhesion to most types of materials: glues steel, cast iron, ferroalloys and non-ferrous metals, wood, fiberboard, concrete, natural and artificial stone, marble, porcelain, polystyrene, etc.

 

Cure mode: 50 min. at a temperature of - 120C

Can be cured with a hardener of a cold hardener.

 

The cured adhesive is characterized by:

  • high strength and tightness characteristics;
  • tightness of the adhesive seam;
  • resistance to cyclic loads, thermal cycling, etc .;
  • resistant to oils, freons, lubricants, water, most organic solvents.

More Email


Is Negotiable

The epoxy adhesive single-pack glue brand УП 5-207

Scientific-Production Enterprise “Synthes”, PE

One-pack (ready-to-use) structural adhesive sealant with increased heat resistance.

The use of this material allows to combine both homogeneous (metal-metal) and heterogeneous materials (ferrous and non-ferrous metals, stone, wood, ceramics, porcelain, plastic, fiberglass.) Special additives allow to exclude operations for cleaning, degreasing and surface preparation from the technological cycle.

It has a complex of properties and can be modified for the specific application of the Customer.

Product Feature:

- stored at room temperature for 4-8 months, in the refrigerator for 1-2 years.

- it is cured when heated to 120-150 C in 15-20 minutes.

- operating temperature range from -100 С to 200 С, for short time 250 С.

- does not contain solvents.

- the ability to glue oily metals.

- retains 90% of properties after aging in oils, lubricating and cooling liquids at 135 C during the year.

- possesses adhesion to a wide range of substrates and provides high adhesion strength: alloyed steel type 30ХГСА (up to 40 MPa), steel 35 (up to 34 MPa), titanium (up to 35 MPa), brass (up to 22 MPa), glass, coal, organic, hybrid plastics (destruction by plastic), ceramics (up to 25 MPa), gold (up to 30 MPa), kovara (up to 9 MPa), beryllium foil, sendasta, permalloy, alloy Neisilber (up to 6 MPa), ABS plastic, polyamide (plastic).

- provides tightness of adhesive joints at an excess pressure of up to 107 Pa or in a deep vacuum (helium leaks less than 3 • 10-7 l μm / s).

-stress to the effect of freon, oils, lubricating-cooling liquids, does not change the optical characteristics of instrument liquids, corrosion activity corresponds to a score of "0", mushroom resistance is 1-2 points.

Methods of application

The application of the material is carried out by Graco pistols, by screen printing. It is allowed to apply with a spatula, brush.

Areas of use

It was developed according to the terms of reference and applied to JSC AVTO-VAZ before the introduction of robotics on the conveyor belt for anticorrosive protection and sealing of glued joints of perimeter flaps of doors, hoods, luggage carriers of VAZ, ZAZ, RAF, AZLK, GAZ.

Currently, the glue is used to paste carbide inserts in the manufacture of cutting tools (cutters, cutters, countersinks, hons, etc.).

Glue has found application for gluing magnets in stators and rotors of electric motors, gluing ceramic inserts in fuses, gluing of dissimilar substrates (fiberglass - copper or steel tip, etc.), bonding difficult-to-digest and hard-to-break metals and alloys (making plate and tubular heat exchangers, radiators from copper, brass, aluminum, duralumin, blocks of cylinders), restoration of bearing seats, manufacturing and installation of sensors, electric motors, etc.

It is also used for the productiion of rotary racks of railway cars. There is an experience of pasting babbitt bearings in the compressor equipment.

It is developed and applied in technology of restoration of necks of shafts, landing places on shafts, shafts gear wheels.

More Email